| ORDERING NUMBER | DESCRIPTION (1) | ECGAM / ECXAM 020 to 170 all design (CH530) ECGAN / ECXAN 209 to 214 all design (CH530) | ECGAN / ECXAN 200 to 400 design A/B/C *(CH532) | ECGAN / ECXAN 200 to 400 design D * (CH532) | ECGAN / ECXAN 200 to 400 design E/F/G/H/J * (CH532) | ECGAN / ECXAN 500 to 925 design A/B/C * (CH532) | ECGAN / ECXAN 500 to 925 design D * (CH532) | |
|---|---|---|---|---|---|---|---|---|
| ADP0063E | ADAPTER SENSOR DIA 6 TO 6.35MM | 1 | 1 | 1 | 1 | 1 | ||
| TDR0019E | TRANSDUCER 1-46 BARS | 1 | 1 | 1 | 1 | 1 | ||
| BRD02102 | POWER SUPPLY CARD CH530 | 1 | ||||||
| BRD04874 | DUAL BOARD HIGH VOLTAGE BINARY INPUT | 1 | ||||||
| BRD04873 | DUAL BOARD BINARY INPUT | 1 | ||||||
| BRD04878 | BOARD DUAL RELAY OUTPUT | 1 | ||||||
| BRD04876 | DUAL BOARD TRIAC OUTPUT | 1 | ||||||
| BRD04879 | CARD 4 RELAY OUTPUT | 1 | ||||||
| BRD04877 | BOARD STARTER | 1 | ||||||
| MOD02092 | MODULE DYNAVIEW | 1 | ||||||
| SEN02133 | SENSOR TEMP | 1 | ||||||
| TDR00354 | TRANSDUCER PRESSURE (PX) LLID 0-475 PSIA | 1 | ||||||
| CON0206E | CONNECTOR PCB 3 POLES | 3 | ||||||
| CON0208E | CONNECTOR PCB 12 POLE | 1 | ||||||
| TDR0018E | TRANSDUCER 0-20 BARS | 1 | 1 | 1 | 1 | 1 | ||
| TDR0014E | TRANSDUCER 0-30 BAR REFRIGERANT | 1 | 1 | 1 | 1 | 1 | ||
| CNT0238E | PRESSURE SWITCH 8/32,0BAR | 1 | 1 | |||||
| CNT0241E | FLOW SWITCH WATER REGULATE 20 CMS | 1 | 1 | 1 | ||||
| CNT0242E | FLOW SWITCH WATER REGULATE 40 CMS | 1 | ||||||
| CNT0273E | PRESSURE SWITCH 8/32.0BAR | 1 | ||||||
| CNT0282E | FLOW SWITCH - 10 BARS | 1 | ||||||
| CNT0305E | FLOW SWITCH - 10 BARS | 1 | ||||||
| CNT0294E | PRESSURE SWITCH HP 25/29.5 BAR | 1 | 1 | 1 | 1 | |||
| MOD0184E | MODULE PCO3 WIDE | 1 | 1 | |||||
| MOD0185E | MODULE PCO3 MEDIUM | 1 | 1 | 1 | ||||
| SEN0011E | SENSOR TEMP -40/+90°C | 1 | 1 | 1 | 1 | 1 | ||
| SEN0103E | SENSOR TEMP -50/+100°C | 1 | 1 | 1 | 1 | 1 | ||
| SEN01960 | SENSOR HIGH TEMP CH530 | 1 | ||||||
| SEN02039 | SENSOR TEMP FAST CH530 | 1 | ||||||
| CON0205E | CONNECTOR PCB 2 POLES | 2 |
1 - Chiller control boards and periphericals generally require programming prior to unit start up. Contact your local Trane representative to obtain information.
